Standard height/full-height PCI Express x16/PCI-X riser board
9.
Optional 3rd
and 4th 3.5” Non-Hot plug SATA or hot plug SAS/SATA hard
drive bays
10.
Standard 1st and 2nd 3.5” Non-Hot plug SATA or hot
plug SAS/SATA hard drive bays
11.
Expansion Slots:
Non-Hot Plug Models – Two available x16 PCI-Express Gen2 slots
Hot Plug Models – One available x16 PCI-Express slot Gen2 slot
What's New
Support for up 400GB 3G 10K 3.5" DP SAS Enterprise Hard Drive
At A Glance
The HP ProLiant DL160 G5 server is an
affordable 1U, dual processor capable server equipped with essential
performance features that provide customers with a platform to design a
fully optimized solution. It is ideal for general purpose and high
performance computing.
Processors:
Supports up to two Intel® Quad-Core 5400 or Dual-Core 5200
sequence processors
Supports up to 64 GB of PC2-5300 (DDR2-667) and up to 32 GB of
PC2-6400 (DDR2-800) fully buffered DIMMs (DDR2-667) with Advanced
ECC
Internal Drive Support:
Support for up to four 3.5" Non-Hot plug serial ATA (SATA) hard
drives or;
Support for up to four 3.5" Hot plug Serial Attached SCSI (SAS)
or SATA hard drives.
NOTE: Installation of the Hot
Plug Backplane 1U 2S Kit (445985-B21) is required if ordering third
or fourth Hard Drives for Hot Plug models only.
Internal storage capacity of up to 1.0TB (4 x 1TB Hot Plug 3.5"
SATA), 3.0TB (4 x 750 Non-Hot Plug SATA) or 4.0TB (4 x 1TB Hot Plug
3.5" SAS)
Network Controller:
Two embedded NC105i PCIe Gigabit Server Adapters
Storage Controllers:
Non-Hot Plug SATA Models: HP Embedded SATA RAID Controller NOTE: Transfer rate: 1.5
Gb/s SATA
Hot Plug SAS/SATA Models: HP SC40Ge 4-Port Internal SAS HBA with
RAID 0, 1 NOTE: When using the SC40Ge
with SATA Hard Drives, 1.5G SATA Hard Drives are required. NOTE: Transfer rate: 1.5 Gb/s SATA, 3Gb/s SAS
Expansion Slots:
Non-Hot Plug Models: Two available PCI Express 2.0 slots:
Slot 2: low-profile/half-height PCI-X slot populated by the
SAS/SATA storage controller
Management:
HP Lights Out 100i Advanced Remote Management with new licensed
key activated upgrades for Virtual KVM and virtual media support.
LO100i management support for the DL160 G5 includes:
IPMI 2.0 & SMASH CLP support
ROM Setup Utility
Improvements to virtual media with the addition of USB 2.0
drives and protocol support for much faster transfer speeds and
DVD-ROM support plus simplified virtual media (floppy and CD with no
FTTP server requirements)
Enhanced browser interface and embedded KVM over IP provides
OS-independent remote graphical console
New Licenses that have EULAs with one-time, optional, license
activation key to allow for easy, future upgrades which will be
chargeable when they become available.
USB Ports:
Five USB ports (two front, one internal, two rear)
Optical Drive:
Support for one (optional): DVD-ROM, DVD/CD RW
Power Supply:
650W Power Supply (Non-Hot Plug, Autoswitching)
Optional high-efficiency model
NOTE: Optional
high-efficiency model requires the purchase of HP Power Supply
Backplane (453652-B21)
Additional Features:
Support for:
NVIDIA Quadro FX3700 512MB PCIe x 16 graphics card
NVIDIA Quadro FX1700 512MB PCIe x 16 graphics card
Form Factor:
Rack (1U)
Fixed mounting rails included with all models
Deployment/Serviceability:
Tool-less access to all system components for easy in rack
serviceability
Customer Self Repair (CSR): HP products are designed with many
CSR parts to minimize repair time and allow for greater flexibility
in performing defective parts replacement
Warranty:
This product is covered by a global limited warranty and supported
by HP Services and a worldwide network of HP Authorized Channel
Partners. Hardware diagnostic support and repair is available for one
year from date of purchase. Support for software and initial setup is
available for 90 days from date of purchase. Enhancements to warranty
services are available through HP Care Pack services or customized
service agreements. SATA hard drives have a one year warranty. SAS
Midline drives have a one-year warranty. SAS Enterprise drives have a
three-year warranty. NOTE: Server Warranty
includes 1 year Parts, 1 year Labor, 1-year on-site support with next
business day response. Warranty repairs may be accomplished through
the use of Customer Self Repair (CSR) parts. These parts fall into two
categories: 1) Mandatory CSR parts are designed for easy replacement.
A travel and labor charge will result when customers decline to
replace a Mandatory CSR part; 2) Optional CSR parts are also designed
for easy replacement but may involve added complexity. Customers may
choose to have HP replace Optional CSR parts at no charge. Additional
information regarding worldwide limited warranty and technical support
is available at:
http://h18004.www1.hp.com/products/servers/platforms/warranty/index.html.
NOTE: For a brief, printer friendly data
sheet that describes this product and informs you of the essential capabilities
and specifications, please visit:
http://h71028.www7.hp.com/ERC/downloads/4AA1-6954ENW.pdf NOTE:
For the Standard Features shipped in the Factory Integrated Models, please see
the "Configuration Information - Factory Integrated Models" section.
Processor One of the following depending on Model
Quad-Core Intel® Xeon® processor X5482 (3.20 GHz, 120W, 1600MHz FSB)
NOTE:
Available through Configure To Order only. See Factory Integration
Models section for more details.
Quad-Core Intel® Xeon® processor X5470 (3.33 GHz, 120W, 1333MHz FSB)
NOTE:
Available through Configure To Order only. See Factory Integration
Models section for more details.
Quad-Core Intel® Xeon® processor X5460 (3.16 GHz, 120W, 1333MHz FSB)
NOTE:
Available through Configure To Order only. See Factory Integration
Models section for more details.
Quad-Core Intel® Xeon® processor L5430 (2.60 GHz, 50W, 1333MHz FSB)
NOTE:
Available through Configure To Order only. See Factory Integration
Models section for more details.
Dual-Core Intel® Xeon® processor
L5240 (3.00 GHz, 40W, TDP, 1333MHz FSB)
NOTE:
Available through Configure To Order only. See Factory Integration Models
section for more details.
Upgradeability
Upgradeable to two processors
Chipset
Intel® 5400
Chipset
Cache Memory
12 MB (2 x 6
MB) Level 2 cache (5400 sequence)
6 MB (1 x 6 MB) Level 2 cache (5200 sequence)
Memory Protection
Advanced ECC capabilities
Memory
Type
PC2-5300
(DDR2-667) and PC2-6400 (DDR2-800)
NOTE:
DIMM banks are active only when the corresponding processor socket is
populated.
Standard
1 GB
(2 x 512 MB)
Maximum
32 GB
64 GB
(8 x 4 GB) PC2-6400
(8 x 8 GB)
Network Controller
Two embedded NC105i PCIe
Gigabit Server Adapters
Expansion Slots #
Technology
Bus Width
Connector Width*
Bus Number*
Device No.**
Form Factor
Notes
1
PCI-Express 2.0
x16
x16
1
0
Full length, full height
3.3 volts
1
PCI-X***
64-bit
N/A
5
1
Full length, full height
3.3 volts
2
PCI-Express 2.0
x16
x16
6
3
Low Profile
3.3 volts
2
PCI-X***
64-bit
N/A
5
1
Low Profile
3.3 volts
NOTE: All slots
can accept universal keyed PCI cards
* Default bus
assignment. Inserting cards with PCI bridges may alter the actual bus
assignment number.
** Slots are
enumerated differently based on OS. MS OS's enumerate from lowest to highest
Device ID by bus (starting with the lowest bus).
*** PCI-X bus speed
will be 133MHz when only one PCI-X card is installed. It will be 100MHz when
both slots have PCI-X cards installed.
Storage Controller
Non-Hot Plug SATA Models
HP Embedded SATA RAID
Controller (integrated into the south-bridge) supporting SW RAID 0,1 NOTE: Transfer rate: 1.5 Gb/s SATA
Hot Plug SATA/SAS Models
HP SC40Ge HBA with RAID 0, 1 NOTE: When using the SC40Ge with
SATA Hard Drives, 1.5G SATA Hard Drives are required. NOTE: Transfer rate: 1.5 Gb/s SATA, 3 Gb/s SAS
NOTE:
A diskette drive, USB floppy drive key or virtual FDD using LO100 Advanced
Pack is needed to install storage controller drivers during a Windows
operating system installation from a CD.
Storage
Optical Drives:
DVD-ROM
8x IDE (ATAPI) DVD-ROM drive,
slim (optional)
DVD/CD RW
24x IDE (ATAPI) CD-ROM drive
(optional)
Diskette Drives
Via USB only
Drive Bays:
Non-Hot Plug SATA
Up to 4 Non-hot plug SATA 3.5"
drives
Hot Plug SATA/SAS
Up to 4 Hot plug SAS/SATA 3.5"
drives
Maximum Internal Storage
Non-Hot Plug SATA
3.0TB
4 x 750GB
Hot Plug SATA
4.0TB
4 x 1TB
Hot Plug SAS
4.0TB
4 x 1TB
Interfaces
Parallel
None
Network RJ-45(Ethernet)
2 10/100/1000 NIC ports (plus
1 dedicated for the HP ProLiant Lights Out 100i Remote Management)
Server Management Stand Alone Software Product and ProLiant Essentials
Lights-Out 100i
HP Lights-Out 100i Remote Management delivers affordable, entry level
remote management capabilities for HP ProLiant 100 Series servers with
embedded LO100i. It allows customers or their service providers to
remotely manage ProLiant 100 Series servers remotely over a LAN or the
Internet and consists of the following:
LO100i Standard is embedded remote management and provides basic
remote control via telnet, browser, and IPMI 2.0 and SMASH
LO100i Advanced Pack License are upgrades for essential, secure,
remote control, serial console, virtual media, and Virtual KVM
(graphical hardware-based, remote console)
NOTE: Flexible and volume quantity
(AKA) license kits are available for the Lights-Out 100i Lights-Out 100
Advanced Pack licenses as well as Electronic License To Use (E-LTU). AKA
Tracking licenses require a 100 unit minimum forecast at initial contract
signing. For these additional part numbers, please refer to each software
products' QuickSpecs at this link for more information:
http://h18004.www1.hp.com/products/servers/management/
remotemgmt.html.
Insight Rapid Deployment Pack
Rapid Deployment Pack (RDP)
extends HP Systems Insight Manager with a complete deployment solution for
HP ProLiant servers. RDP provides a central location to configure server
hardware, deploy Windows, Linux and VMware ESX operating environments and
install using images and scripted profiles. For more information, visit:
http://www.hp.com/go/rdp. NOTE: Flexible and volume quantity
license kits are available for ProLiant Essentials Value Packs. Refer to:
http://www.hp.com/servers/proliantessentials
or the various Insight Essentials Value Pack product QuickSpecs for more
information.
HP Systems Insight Manager
HP Systems Insight Manager (HP SIM) provides a unified, secure and
extensible standards-based environment to centrally manage servers,
storage and other infrastructure devices, (both HP and non-HP) across
multiple operating system platforms.
Core
Infrastructure Management
Subscriber's Choice
Subscriber's Choice Driver and Support Alerts/Notifications is a
web-based email subscription service that provides software and driver
change notifications for ProLiant products. Sign up at:
http://www.hp.com/go/subscriberschoice
and customize your profile to receive various new alerts as they become
available, on a weekly or monthly basis.
ROMPaq, software and latest
drivers
The latest software, drivers,
and firmware fully optimized and tested for your ProLiant server and
options, available through software and drivers download pages website at:
http://www.hp.com/go/support.
HP Serviceguard for Linux (SG/LX)
HP Serviceguard for Linux is a high availability clustering solution
designed to protect applications and services from a wide variety of
software and hardware failures, monitoring the health of each server (node)
and quickly responding to failures such as those that affect system
processes, system memory, LAN media and adapters, and application processes.
The following is a quick summary of HP Serviceguard for Linux features and
support. For the most recent list of Linux distributions & kernels, servers
and storage supported with Serviceguard for Linux, see the Serviceguard for
Linux Datasheet, available at:
http://www.hp.com/go/sglx/info.
Supported Linux
Distributions:
Red Hat EL 4
Red Hat EL 5
SUSE
SLES10
Supported Server Platforms
HP
Integrity BladeSystem to Superdome
HP ProLiant BladeSystem
p-Class & c-Class
HP ProLiant DL
HP ProLiant ML
IBM System x
Dell PowerEdge
Sun x64
Fujitsu
Siemens PRIMERGY
Supported Virtual Machines
SG/LX in HP Integrity Virtual Machines guests
SG/LX in
VMware ESX guests
SG/LX in Red Hat and SUSE Xen hosts (DOM0)
Application Integration Toolkits
HP Serviceguard
for Linux Oracle Database Toolkit
HP Serviceguard Extension
for SAP on Linux (SGeSAP/LX)
Free Application Integration
Toolkits:
Apache
MySQL
NFS
PostgreSQL
Samba
Tomcat
Sendmail
Disaster Tolerant Solutions
HP Serviceguard
for Linux Extended Distance Cluster (XDC) extends cluster distances
up to 100 km, utilizes software RAID mirroring for data replication
and is storage array independent
HP StorageWorks XP/EVA
Cluster Extension Software for Linux (CLX) works seamlessly with HP
Serviceguard for Linux, HP StorageWorks Continuous Access, and HP
Disk Arrays to automate failover and failback between sites
Software updates are distributed by HP Services to customers with
support contracts
NOTE:
For additional information on HP Serviceguard for Linux, visit:
http://www.hp.com/go/sglx
or see the HP Serviceguard for Linux QuickSpecs. NOTE: HP
Serviceguard for Linux products for HP ProLiant and select 3rd party x86
class servers include one year of 24 x 7 HP Software Technical Support and
Update Service ensuring rapid access to HP support staff and proactive
delivery of software updates. For more information about this service,
please visit:
http://www.hp.com/services/swsupport.
Industry Standard
Compliance
ACPI V2.0 Compliant
PCI 2.2 Compliant
PXE Support
WOL Support
Microsoft® Logo certifications
IPMI 2.0, SMASH CLP compliant
Manageability
HP Lights-Out 100i Standard provides the following OS-independent
remote control capabilities:
Virtual power
System event log access
System health
Remote serial console (serial redirection)
Browser, Telnet access
SMASH-CLP compliant
IPMI 2.0 compliant
HP Lights-Out 100i Advanced Pack provides license key activated
upgrades to the following:
Virtual KVM (KVM over IP functionality embedded on the system board)
Security
Power-on password
Setup password
Server Power Cords
One
6' Highline (IEC-IEC) power cord ships standard
NOTE:
HP ProLiant DL servers no longer ship standard with NEMA power cords
(163719-002) that allow connection to 110V US wall outlets in a home or
office. ProLiant DL servers are primarily connected to PDU's in data center
racks so they now ship standard with only a PDU power cord (416151-B21). If
a user wishes to power a ProLiant DL server using a 110V receptacle
(NEMA-15), the NEMA power cord (227099-001) must be ordered separately.
If customers require a local power cord, they can check the power cord
matrix for the appropriate cord. Please see the following power cord matrix:
http://www.hp.com/go/powercordmatrix.
NOTE: For more information on HP's
Certified and Supported ProLiant Servers for OS and Virtualization Software
and latest listing of software drivers available for your server, please
visit our Support Matrix at:
http://www.hp.com/go/supportos
and our driver download page
http://www.hp.com/support/DL160G5.
Rack Airflow Requirements
Rack 10000 series Cabinets The increasing power of new
high-performance processor technology requires increased cooling efficiency
for rack-mounted servers. The 10000 Series Racks provide enhanced airflow
for maximum cooling, allowing these racks to be fully loaded with servers
using the latest processors.
CAUTION:
If a third-party rack is used, observe the following additional requirements
to ensure adequate airflow and to prevent damage to the equipment:
Front and rear doors: If your 42U server rack includes closing front and
rear doors, you must allow 5,350 sq cm (830 square inches) of hole evenly
distributed from top to bottom to permit adequate airflow (equivalent to the
required 64 percent open area for ventilation). Side: The clearance
between the installed rack component and the side panels of the rack must be
a minimum of 7 cm (2.75 inches)
CAUTION: Always use blanking
panels to fill all remaining empty front panel U-spaces in the rack. This
arrangement ensures proper airflow. Using a rack without blanking panels
results in improper cooling that can lead to thermal damage.
NOTE: For
additional information, refer to the Setup and Installation Guide or the
Documentation CD provided with the server, or to the server documentation
located in the Support section at the following URL:
www.hp.com/servers/dl160.
Rack Support
The DL Fixed Rail System
supports installation in racks with square or round mounting holes
(including Compaq/HP 7000, 9000, 10000 and HP series), with an adjustment
range of 24" - 36". Installation into Telco 2 post, and 4 post, or threaded
holes racks requires a 3rd party option kit. For additional information,
please visit: www.racksolutions.com.
Factory Express Portfolio for
Servers and Storage
HP Factory Express offers
configuration, customization, integration and deployment services for HP
servers and storage products. Customers can choose how their factory
solutions are built, tested, integrated, shipped and deployed.
Factory Express offers service packages for simple configuration, racking,
installation, complex configuration and design services as well as
individual factory services, such as image loading, asset tagging, and
custom packaging. HP products supported through Factory Express include a
wide array of servers and storage: HP Integrity, HP ProLiant, HP ProLiant
Server Blades, HP BladeSystem, HP 9000 servers as well as the MSAxxxx,
VA7xxx, EVA, XP, rackable tape libraries and configurable network switches.
For more information on Factory Express services for your specific server
model please contact your sales representative or go to:
http://www.hp.com/go/factory-express.
HP Enterprise Configurator
The HP eConfigure Enterprise Configurator now provides factory default
racking for our HP hardware portfolio. This approach is aligned with our
strategic direction to meet the needs and expectations of our valued
customers. If you require "custom" rack configuration, please contact HP's
Customer Business Center or an Authorized Partner for assistance.
Service and Support
HP Care Pack Services provide total care and support expertise with
committed response designed to meet your IT and business needs.
HP Care Pack Services provide total care and support expertise with
committed response designed to meet your IT and business needs.
HP Care Pack services include coverage for the HP branded hardware
options qualified for the server that are purchased at the same time or
afterward and internal to the enclosure. It also includes the 22" and
smaller external monitors and tower UPS options up to 3kVA. These items
will be covered at the same service level and for the same coverage period
as the server. Coverage of UPS Battery is not included and standard
warranty terms & conditions apply. For servers or storage systems
installed within a rack, service also covers all HP qualified rack options
installed within the same rack.
To fully capitalize on your HP ProLiant servers' capabilities requires
a service partner who thoroughly understands your server technology and
systems environment. HP Services, an industry leader in provision of multi
vender support solutions provides a range of support services designed to
meet the varying needs of business. Whether an SMB or large global
corporation HP has a ProLiant server support offer to help you speedily
deploy and maximize system uptime.
Recommended Service – Simplify ProLiant solution implementation,
maintenance and management.
Support Service – 3 Year, 9x5 Next Business Day coverage,
excluding HP holidays only
Deployment Service – Hardware Installation only
Enhanced Service – Optimize service level to increase IT
performance and availability
Support Service – 3 Year 13x5 Same Business Day, 4-Hour
response coverage
Deployment Service – Installation and Start-up only
Installation & Start-Up of a ProLiant server and Microsoft or Linux O/S
per the Customer Description and/or Data Sheet. To be delivered on a
scheduled basis 8am-5pm, M-F, excl. HP holidays.
NOTE:
High Performance Computing (HPC) interconnect technologies are available
for the DL160 G5 under the Cluster Platform product portfolio. These
high-speed interconnects are fully supported by HP when they are part of
these configure to order clusters. Solutions can be defined with a lot of
flexibility with the help of configuration tools. Please visit the following
URL to configure HPC Clusters with InfiniBand, Gigabit Ethernet or Myrinet
Interconnects:
http://www.hp.com/techservers/clusters/ucp/index.html
Non-Hot Plug
Serial ATA (SATA) Models NOTE: Non-Hot Plug models are not
upgradeable to Hot Plug. Non-Hot Plug models require the addition of the HP
HBA SAS-SATA 4x1LN Cable Kit (P/N: 452130-B21) in order to connect a
hardware RAID controller.
HP DL160 G5 X5472 Non-Hot Plug SATA, 2GB, (1P)
445198-xx1
HP DL160 G5 E5430 Non-Hot Plug SATA, 1GB, (1P) 445197-xx1
HP DL160 G5 E5405 Non-Hot Plug SATA, 1GB, (1P) 445196-xx1
Processor(s) One of the following depending on model
Configuration Information - Factory Integrated Models
NOTE: This section lists some of the steps required to configure
a Factory Integrated Model. To ensure only valid configurations are
ordered, HP recommends the use of an HP approved configurator. Contact
your local sales representative for additional information. NOTE: HP does not allow factory integration of options into
standard models listed above. Configure-to-order servers must start with a
CTO Chassis.. NOTE: FIO indicates that this option is a Factory Installable
Option.
Step 1: Base Configuration (choose one of the following configurable
models)
Non-Hot Plug SATA Model NOTE: Non-Hot Plug models are not
upgradeable to Hot Plug. Non-Hot Plug models require the addition of the HP
HBA SAS-SATA 4x1LN Cable Kit (P/N: 452130-B21) in order to connect a
hardware RAID controller.
HP ProLiant DL160 G5 Non-Hot
Plug SATA Rack CTO Chassis
445192-B21
Factory
Integrated Model ships with:
Two embedded NC105i PCIe
Gigabit Server Adapters (WOL & PXE-capable)
Step 2: Choose Required Options (only one of the following from each list
unless otherwise noted)
Processors
Quad-Core
Processors
Quad-Core Intel® Xeon® processor X5482 (3.20 GHz, 120W, 1600MHz FSB), FIO
NOTE:
If 2 processors are desired, select one 495614-L21 and one 495614-B21.
495614-L21
Quad-Core Intel® Xeon®
processor X5472 (3.00 GHz, 120W, 1600MHz FSB), FIO
NOTE:
If 2 processors are desired, select one 462465-L21 and one 462465-B21.
462465-L21
Quad-Core Intel® Xeon® processor X5470 (3.33 GHz, 120W, 1333MHz FSB), FIO
NOTE:
If 2 processors are desired, select one 495612-L21 and one 495612-B21.
495612-L21
Quad-Core Intel® Xeon®
processor X5460 (3.16 GHz, 120W, 1333MHz FSB), FIO
NOTE:
If 2 processors are desired, select one 446085-L21 and one 446085-B21.
446085-L21
Quad-Core Intel® Xeon® processor L5430 (2.60 GHz, 50W, 1333MHz FSB), FIO
NOTE:
If 2 processors are desired, select one 495616-L21 and one 495616-B21.
495616-L21
Quad-Core Intel® Xeon®
processor L5420 (2.50 GHz, 50W, 1333MHz FSB), FIO
NOTE:
If 2 processors are desired, select one 495479-L21 and one 495479-B21.
495479-L21
Quad-Core Intel® Xeon® processor L5410 (2.33 GHz, 50W, 1333MHz FSB), FIO
NOTE:
If 2 processors are desired, select one 448369-L21 and one 448369-B21.
448369-L21
Quad-Core Intel® Xeon® processor E5472 (3.00 GHz, 80W, 1600MHz FSB), FIO
NOTE:
If 2 processors are desired, select one 448365-L21 and one 448365-B21.
448365-L21
Quad-Core Intel® Xeon® processor E5462 (2.80 GHz, 80W, 1600MHz FSB), FIO
NOTE:
If 2 processors are desired, select one 463076-L21 and one 463076-B21.
463076-L21
Quad-Core Intel® Xeon® processor E5430 (2.66 GHz, 80 W, 1333 MHz FSB), FIO
NOTE:
If 2 processors are desired, select one 446079-L21 and one 446079-B21.
446079-L21
Quad-Core Intel® Xeon® processor E5405 (2.00 GHz, 80W, 1333MHz FSB), FIO
NOTE:
If 2 processors are desired, select one 446077-L21 and one 446077-B21.
446077-L21
Dual-Core Processors
Dual-Core Intel® Xeon®
processor X5272 (3.40 GHz, 80W, 1600MHz FSB)
NOTE:
If 2 processors are desired, select one 448371-L21 and one 448371-B21.
448371-L21
Dual-Core Intel® Xeon®
processor L5240 (3.00 GHz, 40W, 1333MHz FSB), FIO
NOTE:
If 2 processors are desired, select one 448373-L21 and one 448373-B21.
448373-L21
Memory
NOTE: DIMM banks
are active only when the corresponding processor socket is populated.
1 GB FBD PC2-5300 2 X 512 MB Kit
397409-B21
2 GB FBD PC2-5300 2 X 1 GB Kit
397411-B21
4 GB FBD PC2-5300 2 X 2 GB Kit
397413-B21
8 GB FBD PC2-5300 2 X 4 GB Kit
397415-B21
Dual Rank
4 GB FBD PC2-6400 800MHz 2 x 2
GB Dual Rank Kit
484060-B21
8 GB FBD PC2-6400 2 x 4 GB Dual
Rank Kit
484062-B21
16 GB FBD PC2-5300 2 x 8 GB Dual
Rank Kit
413015-B21
64 GB FBD PC2-5300 8 x 8 GB Dual
Rank Kit
495604-B21
Low Power
2 GB FBD PC2-5300 2 X 1 GB Low
Power Kit
461826-B21
4 GB FBD PC2-5300 2 x 2 GB Low
Power Kit
461828-B21
8 GB FBD PC2-5300 2 x 4 GB Low
Power Kit
466440-B21
Hard Drive
NOTE: Transfer
rates of drives are dependent on the maximum transfer rate supported by the
HBA or Controller. Refer to the HBA or Controller technical specifications
for details.
NOTE: A minimum
of one hard drive is required when purchasing Non-Hot Plug CTO Chassis Model
(P/N 445192-B21). NOTE: SATA Non-Hot Plug Hard Drives ONLY required when purchasing
Non-Hot Plug CTO Chassis Models (445192-B21) in Step 1.
Serial-ATA (SATA) Non-Hot
Plug Hard Drives (Non-Hot Plug Models Only)
SATA Non-Hot Plug Midline (MDL)
Drive
HP 750GB 3G SATA 7.2K NHP 3.5"
MDL HDD
462595-B21
HP 500GB 3G SATA 7.2K NHP 3.5"
MDL HDD
458941-B21
HP 250GB 3G SATA 7.2K NHP 3.5" MDL HDD
458939-B21
SATA Non-Hot Plug Entry (ETY)
Drives
HP 160GB 3G SATA 7.2K NHP 3.5"
ETY HDD
458947-B21
SATA Non-Hot Plug
HP 500GB 1.5G SATA 7.2K NHP 3.5"
HDD, FIO
404469-B21
Storage Controllers
NOTE: A minimum
of one SAS Controller is required when purchasing Hot Plug CTO Chassis Model
(P/N 445193-B21). NOTE: The below storage controllers are intended for use with
internal drives ONLY in the Hot Plug CTO Chassis Model (P/N 445193-B21).
HP SC44Ge Host Bus Adapter NOTE: When using the SC44Ge with
SATA Hard Drives, 1.5G SATA Hard Drives are required. Transfer rate: 1.5
Gb/s SATA, 3 Gb/s SAS.
416096-B21
HP SC40Ge 4 Internal PCIe SAS
RAID Half Height HBA, FIO NOTE: Recommended HBA when
purchasing Hot Plug CTO Chassis Model (P/N 445193-B21). NOTE: When using the SC40Ge with SATA Hard Drives, 1.5G SATA Hard
Drives are required. Transfer rate 1.5 Gb/s SATA, 3 Gb/s SAS.
449363-B21
HP Smart Array E500/256MB
Controller with Battery, FIO NOTE: Customers can only order one
Smart Array E500/256MB Controller and one Battery-backed write cache upgrade
(P/N 383280-B21) for the HP ProLiant DL160 G5 server based on battery space.
462105-B21
HP Smart Array E200/128 BBWC Controller
411508-B21
HP HBA SAS-SATA 4x1LN Cable Kit
452130-B21
NOTE: This
option is required for any internal port HBA or controller that has a
standard 4 port SAS/SATA connector.
Step 3: Choose
Additional Factory Integratable Options (only one of the following from each
list unless otherwise noted)
Power Supply
HP High Efficiency Power Supply
Kit, FIO NOTE: Selection of the HE Power
Supply Unit will remove the 650 Watt standard power supply and requires the
purchase of Power Supply Backplane (p/n 453652-B21).
453650-B21
HP Power Supply Backplane, FIO NOTE: This backplane must be
ordered with the High Efficiency Power Supply (P/N 453650-B2).
453652-B21
Step 4: Choose Additional
Options for Factory Integration
NOTE: For
additional options, please refer to the "Core Options" and "Additional
Options" section below. Some options may not be available for factory
integration. Please contact an HP sales representative for additional
information.
NOTE: DIMM banks
are active only when the corresponding processor socket is populated.
1 GB FBD PC2-5300 2 X 512 MB Kit
397409-B21
2 GB FBD PC2-5300 2 X 1 GB Kit
397411-B21
4 GB FBD PC2-5300 2 X 2 GB Kit
397413-B21
8 GB FBD PC2-5300 2 X 4 GB Kit
397415-B21
Dual Rank
4 GB FBD PC2-6400 2 X 2 GB Dual
Rank Kit
484060-B21
8 GB FBD PC2-6400 2 x 4 GB Dual
Rank Kit
484062-B21
16 GB FBD PC2-5300 2 x 8 GB Dual
Rank Kit
413015-B21
64 GB FBD PC2-5300 8 x 8 GB Dual
Rank Kit
495604-B21
Low Power
2 GB FBD PC2-5300 2 X 1 GB Low
Power Kit
461826-B21
4 GB FBD PC2-5300 2 x 2 GB Low
Power Kit
461828-B21
8 GB FBD PC2-5300 2 x 4 GB Low
Power Kit
466440-B21
Optical Drives
DVD-ROM Drive (optional)
447889-B21
DVD/CD RW Drive (optional)
447891-B21
Hard Drives
NOTE: Transfer
rates of drives are dependent on the maximum transfer rate supported by the
HBA or Controller. Refer to the HBA or Controller technical specifications
for details.
SATA
Non-Hot Plug Midline (MDL) Drives (Non-Hot Plug Models Only)
HP 750GB 3G SATA 7.2K NHP 3.5"
MDL HDD
462595-B21
HP 500GB 3G SATA 7.2K NHP 3.5"
MDL HDD
458941-B21
HP 250GB 3G SATA 7.2K NHP 3.5"
MDL HDD
458939-B21
SATA Non-Hot Plug Entry (ETY)
Drives
HP 160GB 3G SATA 7.2K NHP 3.5"
ETY HDD
458947-B21
SATA Hot Plug Midline (MDL)
Drives (SAS/SATA Hot Plug Models Only) NOTE: A SAS HBA or Array Controller
is required.
NOTE: Electronic
licensing options are available for Insight Control suites and select
Insight Essentials software products. Please see the appropriate Insight
Control and ProLiant Essentials QuickSpecs for additional information.
Control
Lights-Out 100i Advanced Pack
HP LO100i Advanced Pack, No
Media 1-Server License including 1 year of 24x7 Technical Support and
Updates
530521-B21
NOTE: Flexible
and volume quantity (AKA) license kits are available for the Lights-Out 100i
Advanced Pack licenses as well as Electronic License To Use (E-LTU). AKA
Tracking licenses require a 100 unit minimum forecast at initial contract
signing. For these additional part numbers, please refer to each software
products' QuickSpecs at this link for more information:
http://h18004.www1.hp.com/products/servers/management/remotemgmt.html.
Deploy
Rapid Deployment Pack
Insight Essentials Rapid
Deployment Pack No Media 1-Server License including 1 year of 24x7 Technical
Support and Updates NOTE: This license allows 1 server
to be deployed and managed via RDP. Customer will receive a printed license
entitlement certificate via physical shipment. The license entitlement
certificate must be redeemed online or via fax in order to obtain the
license activation key(s). Includes one year of 24 x 7 HP Software Technical
Support and Update Service.
NOTE: Flexible
and volume quantity license kits are available for Insight Essentials Value
Packs. Refer to:
http://www.hp.com/servers/proliantessentials
or the various Insight Essentials Value Pack product QuickSpecs for more
information.
Graphic Cards
HP Nvidia Quadro FX1700 512 MB
PCI-E 16x Kit
490646-B21
HP Nvidia FX3700 512 MB PCI-E
16x Kit
490062-B21
Hot Plug HDD
Backplane Option
Hot Plug HDD Backplane 1U 2S Kit
445985-B21
NOTE:
Installation of the Hot Plug Backplane 1U 2S Kit (445985-B21) is required
if ordering third or fourth Hard Drives for Hot Plug models only.
Storage
Controllers
NOTE: The
addition of storage controllers for internal hard drive use is intended for
use ONLY with the Hot Plug SATA/SAS Model Chassis (P/N 445148-B21).
SAS HBA
HP 8 Internal Port SAS HBA with
RAID NOTE: For use with Hot Plug SAS/SATA models. NOTE: The selection HP 8 Internal Port SAS HBA with RAID requires
the purchase of the LowProfile PCI-X Riser Option kit (P/N 452698-B21) NOTE: Transfer rate: 1.5 Gb/s SATA, 3 Gb/s SAS
347786-B21
HP SC44Ge Host Bus Adapter NOTE: PCI-Express SAS HBA. NOTE: When using the SC44Ge with SATA Hard Drives, 1.5G SATA Hard
Drives are required. Transfer rate: 1.5 Gb/s SATA, 3 Gb/s SAS.
HP Smart Array E500/256MB
Controller
NOTE: Standard RAID 0,1, 1+0. NOTE: Customers can only order one Smart Array E500/256MB
Controller and one Battery-backed write cache upgrade (P/N 383280-B21) for
the HP ProLiant DL160 G5 server based on battery space.
HP Smart Array P400/256
Controller NOTE: Customers can only order one
Smart Array P400/256MB Controller and one Battery-backed write cache upgrade
(P/N 383280-B21) for the HP ProLiant DL160 G5 server based on battery space.
405132-B21
HP Smart Array P400/512
Controller with BBWC NOTE: Customers can only order one
Smart Array P400/512MB BBWC Controllers for the HP ProLiant DL160 G5 server
based on battery space.
411064-B21
512MB Battery-backed write cache
upgrade NOTE: Contains batter and memory
module. For Smart Array P400 Controller.
HP StorageWorks 1U USB
Rack-Mount Kit with one DAT 160 USB Tape Drive NOTE: Pre-configured with one DAT
160 USB tape drive.
AG703A
SAS
Rack-Mount Tape Drives NOTE: HP recommends purchasing the
HP SC44Ge HBA (416096-B21) for a dedicated SAS HBA for tape.
HP StorageWorks 1U SAS
Rack-Mount Kit with one LTO-4 Ultrium 1760 NOTE: Pre-configured with one LTO-4
Ultrium 1760 SAS tape drive.
EH946A
HP StorageWorks 1U SAS
Rack-Mount Kit NOTE: Supports up to (2)
half-height SAS tape drives.
AE459A
HP StorageWorks DAT 160 SAS
Internal Tape Drive NOTE: Mounts inside the 1U SAS
Rack-Mount Kit (AE459A)
Q1587A
HP StorageWorks LTO-2 Ultrium
448 SAS Internal Tape Drive NOTE: Mounts inside the 1U SAS
Rack-Mount Kit (AE459A)
DW085A
HP StorageWorks LTO-3 Ultrium
920 SAS Internal Tape Drive NOTE: Mounts inside the 1U SAS
Rack-Mount Kit (AE459A)
EH847A
SCSI
Rack-Mount Tape Solutions NOTE: SCSI Controller required. HP
recommends purchasing the HP SC11Xe HBA (412911-B21) for a dedicated SCSI
HBA for tape.
HP StorageWorks 1U SCSI
Rack-mount kit with one LTO-2 Ultrium 448 SCSI Tape Drive (Carbonite) NOTE: Pre-configured with one LTO-2
Ultrium 448 SCSI tape drive.
DW028B
HP StorageWorks 1U SCSI
Rack-mount kit with one LTO-3 Ultrium 920 NOTE: Pre-configured with one LTO-3
Ultrium 920 SCSI tape drive.
EH903A
HP StorageWorks 3U SCSI
Rack-Mount with 1 LTO-4 Ultrium 1840 Tape Drive NOTE: Pre-configured with one LTO-4
Ultrium 1840 SCSI tape drive.
EH926A
For an up-to-date
listing of the latest O/S and software support details for HP Ultrium tape
drives, please visit:
http://www.hp.com/go/connect
Disk-Based Backup
RDX Removable Disk Backup
HP StorageWorks RDX160 External
Removable Disk Backup System NOTE: 160GB of Disk Storage
AJ766A
HP StorageWorks RDX320 External
Removable Disk Backup System NOTE: 320GB of Disk Storage
AJ768A
HP StorageWorks RDX500 External
Removable Disk Backup System NOTE: 500GB of Disk Storage
HP StorageWorks 1/8 G2 LTO-4
Ultrium 1760 SAS Tape Autoloader
AK377A
HP StorageWorks 1/8 G2 LTO-3
Ultrium 920 SAS Autoloader
AH558A
HP StorageWorks 1/8 G2 LTO-2
Ultrium 448 Tape Autoloader
AH164A
HP StorageWorks 1/8 G2 Tape
Autoloader Rack Kit NOTE: Required to install the 1/8
G2 Autoloaders in a standard 19-inch rack; includes rails and rackmount
instructions.
AH166A
NOTE: Please
see the QuickSpecs for Technical Specifications and additional information:
http://www.hp.com/go/automation
needed to create a complete solution; reference current compatibility
information at: http://www.hp.com/go/ebs.
Tape Libraries
HP StorageWorks MSL2024 Tape
Library
HP StorageWorks MSL2024 1 LTO-4
Ultrium 1840 SCSI Drive Library
AJ033A
HP StorageWorks MSL2024 1 LTO-4
Ultrium 1760 SAS Drive Library
AK378A
HP StorageWorks MSL2024 1 LTO-3
Ultrium 960 SCSI Drive Library
AG115A
HP StorageWorks MSL2024 1 LTO-3
Ultrium 920 SAS Drive Library
AH559A
HP StorageWorks MSL2024 1 LTO-2
Ultrium 448 SCSI Drive Library
AG116A
HP StorageWorks MSL4048 Tape
Library
HP StorageWorks MSL4048 1
Ultrium 920 SAS Drive Library
AH560A
HP StorageWorks MSL4048 1
Ultrium 960 SCSI Drive Library
AG322A
HP StorageWorks MSL4048 2 LTO-4
Ultrium 1760 SAS Drive Library
AK380A
HP StorageWorks MSL4048 1 LTO-4
Ultrium 1840 SCSI Drive Library
AJ035A
NOTE: Please see
the QuickSpecs for Technical Specifications and additional information:
http://www.hp.com/go/automation
needed to create a complete solution; reference current compatibility
information at: http://www.hp.com/go/ebs.
High Availability
Cluster Options
HP Serviceguard for Linux
HP Serviceguard for Linux on HP
ProLiant and other third-party x86 Servers - Physical Media Kit NOTE: This kit contains media only.
519353-B21
HP Serviceguard for Linux on HP
ProLiant and other third-party x86 Servers Single-Server License
Licensed per Server NOTE: This license allows
Serviceguard for Linux to be installed on 1 server. Customer will receive a
printed license entitlement certificate via physical shipment. The license
entitlement certificate must be redeemed online or via fax in order to
obtain the license activation key(s). Includes one year of 24 x 7 HP
Software Technical Support and Update Service.
519354-B21
HP Serviceguard for Linux -
Flexible-Quantity License
(for HP ProLiant and other third-party x86 servers)
Licensed per Server NOTE: This part number can be used
to purchase multiple licenses with a single activation key. Customer will
receive a printed license entitlement certificate via physical shipment. The
license entitlement certificate must be redeemed online or via fax in order
to obtain the license activation key(s). Includes one year of 24 x 7 HP
Software Technical Support and Update Service.
519355-B21
HP Serviceguard Linux Oracle
Database Toolkit for HP ProLiant/x86 Servers
Licensed per cluster
Includes media and One Year 24x7 Software Support & Updates
463833-B21
HP Serviceguard Extension for
SAP on Linux for HP ProLiant/x86 Servers
Licensed per physical server
Includes media and One Year 24x7 Software Support & Updates
463834-B21
HP Serviceguard Linux Extended
Distance Cluster (XDC) for HP ProLiant/x86 Servers
Licensed per physical server
Includes media and One Year 24x7 Software Support & Updates
463835-B21
NOTE: The above
is not a complete list of all HP Serviceguard for Linux product numbers For
a detailed list of supported configuration/certification options for HP
Serviceguard for Linux please refer to the HP Serviceguard for Linux
Configuration & Ordering Guide available at:
http://www.hp.com/go/sglx/info. NOTE: HP Serviceguard for Linux products running on x86 platforms
now include one year of 24 x 7 Software Technical Support and Updates.
Please see the Support Information section of the HP Serviceguard for Linux
QuickSpecs for details. NOTE: For additional information including a complete list of
Product Numbers for HP Serviceguard for Linux, please see the following
QuickSpecs at:
http://h18000.www1.hp.com/products/quickspecs/11518_div/11518_div.html
(Worldwide)
HP StorageWorks FC2242SR Dual
Channel 4 Gb PCI-e HBA
A8003A
HP StorageWorks FC1142SR 4Gb
PCI-e HBA
AE311A
HP StorageWorks FC1242SR Dual
Channel 4 Gb PCI-e HBA
AE312A
HP StorageWorks FC2143 4Gb PCI-X 2.0 - to Fibre Channel HBA
AD167A
HP StorageWorks FC2243 Dual Channel 4Gb PCI-X 2.0 HBA
AD168A
HP StorageWorks 81E 8Gb SP
PCI-e FC HBA
AJ762A
HP 82E 8Gb Dual-port PCI-e FC
HBA
AJ763A
HP 82Q 8Gb Dual Port PCI-e FC
HBA
AJ764A
StorageWorks SCSI HBA
HP U320e SCSI Host Bus Adapter NOTE: Recommended Dual Channel Ultra320
SCSI Controller for connecting multi-drive MSL tape libraries to ProLiant
servers
AH627A
HP StorageWorks FC2243 4Gb
PCI-X 2.0 DC HBA
AD168A
HP StorageWorks 50 Modular Smart Array
HP StorageWorks 50 Modular Smart Array
364430-B21
NOTE:
Rack-mountable 10 SFF drive enclosure with single I/O module, redundant hot
plug power supplies and hot plug fans. NOTE: Please see the
QuickSpecs for Technical Specifications and additional information:
http://h18000.www1.hp.com/products/quickspecs/12245_div/12245_div.html
(Worldwide)
HP StorageWorks 60 Modular Smart Array
HP StorageWorks 60 Modular Smart Array
418408-B21
NOTE:
Rack-mountable 12-drive (3.5" 3G SAS/1.5G SATA) 2U enclosure with 3Gb/s SAS
host connectivity and redundant power supplies. NOTE: Please see
the QuickSpecs for Technical Specifications and additional information:
http://h18000.www1.hp.com/products/quickspecs/12627_div/12627_div.html
(Worldwide)
HP StorageWorks 70 Modular Smart Array
HP StorageWorks 70 Modular Smart Array
418800-B21
NOTE:
Rack-mountable 25-drive (2.5" 3G SAS/1.5G SATA) 2U enclosure with 3Gb/s SAS
host connectivity and redundant power supplies. NOTE: Please see
the QuickSpecs for Technical Specifications and additional information:
http://h18000.www1.hp.com/products/quickspecs/12652_div/12652_div.html
(Worldwide)
PS/2 Virtual Media Interface
Adapter, 1 pack NOTE: Requires PS/2 and one USB
port on server.
AF604A
HP Server Console Switch (KVM),
0 x 2 x 8 port
AF616A
HP Server Console Switch (KVM),
0 x 2 x 16 port
AF617A
PS/2 Interface Adapter, 1 pack
262588-B21
PS/2 Interface Adapter, 8 pack
262587-B21
HP 1x4 Console Switch
AF611A
HP PS2 Server Console Cable, 6
foot, 2-Pack
AF612A
HP USB Server Console Cable, 6
foot, 2-Pack NOTE: required for supporting USB
peripherals.
AF613A
NOTE: Cat5e
cables are required to connect Interface Adapters to Console Switches. Cat5e
cables can be found at the following URL:
http://www.hp.com/go/kvm
HP Serial Console
Server Options
HP 16 Port Serial Console Server
(worldwide)
AF101A
HP 48 Port Serial Console Server
(worldwide)
AF102A
Serial Adapter, RJ45-D89 DCE
Female, 1-pack
AF103A
Serial Adapter, RJ45-D89 DCE
Female, 8-pack
AF110A
NOTE:
For additional information regarding KVM switches, Serial Console servers,
rack mount monitors, keyboards and all related options please see the
following URL: http://www.hp.com/go/kvm
Service and Support Offerings (HP Care Pack
Services)
Hardware
Services 4-Hour On-site Service
13-Hour x 5-Day Coverage, 3
Years, Electronic
U9509E
24-Hour x 7 Day Coverage, 3
Years, Electronic
U9510E
Hardware Services Next
Business Day On-Site Service
9-Hour x 5-Day Coverage, 3
Years, Electronic
U9508E
Hardware Services 6-Hour
Call to Repair On-Site Service
NOTE:
Memory configurations listed do not apply to "Factory Integrated Models".
Standard
Memory
1GB (2x512MB) or 2GB (2 x 1GB) depending on model, PC2-5300 Fully Buffered
DIMM memory, with Advanced ECC.
Maximum Memory
Up to 32GB memory is available with the optional installation of PC2-5300
Fully Buffered DIMM memory kits. NOTE: Memory should be installed in
pairs and matched for optimum performance.
NOTE:
Chart does not represent all possible memory configurations. NOTE: DIMM banks are active only when the corresponding processor
socket is populated.
Four Non-hot plug SATA
or four 3.5" Hot-plug SAS/SATA hard drive bays
A
Optional DVD-ROM, or
DVD/CD RW
Drive Support
Removable Media
Quantity Supported
Position Supported
Controller
DVD-ROM
Up to 1
A
Integrated IDE (ATAPI) (optional)
DVD/CD RW
Up to 1
A
Integrated IDE (ATAPI) (optional)
Hard Drives NOTE:
Transfer rates of drives are dependent on the maximum transfer rate
supported by the HBA or Controller. Refer to the HBA or Controller
technical specifications for details.
SATA Non-Hot Plug
Midline (MDL) Drives 3.5"
Quantity
Supported
Position
Supported
Controller
250GB 1.5G SATA 7.2K
500GB 1.5G SATA 7.2K
750GB 1.5G SATA 7.2K
Up to 4
1-4
HP Embedded SATA RAID Controller
NOTE: Transfer rate: 1.5 Gb/s SATA
SATA Non-Hot Plug
Entry (ETY) Drives 3.5"
Quantity
Supported
Position
Supported
Controller
160GB 1.5G SATA 7.2K
Up to 4
1-4
HP Embedded SATA RAID Controller NOTE: Transfer rate: 1.5 Gb/s SATA
SATA Non-Hot Plug
Drives
Quantity
Supported
Position
Supported
Controller
160GB 1.5G SATA
250GB 1.5G SATA
500GB 1.5G SATA, FIO
Up to 4
1-4
HP Embedded SATA RAID Controller NOTE: Transfer rate: 1.5 Gb/s SATA
SATA Hot Plug Midline (MDL) Drives 3.5" NOTE: Installation of the Hot Plug
Backplane 1U 2S Kit (445985-B21) is required if ordering third or fourth
Hard Drives for Hot Plug models only.
Quantity
Supported
Position
Supported
Controller
160GB 3G SATA 7.2K
250GB 3G SATA 7.2K
500GB 3G SATA 7.2K
750GB 3G SATA 7.2K
1TB 3G SATA 7.2K
Up to 4
1-4
HP SC40Ge 4-Port Internal SAS
HBA with RAID 0, 1 NOTE: When using the SC40Ge with
SATA Hard Drives, 1.5G SATA Hard Drives are required. Transfer rate: 1.5
Gb/s SATA, 3 Gb/s SAS
HP Smart Array P400 Controller
HP Smart Array P800 Controller
3.5" SATA Hot Plug
Quantity
Supported
Position
Supported
Controller
160GB 1.5G SATA 7.2K
250GB 1.5G SATA 7.2K
500GB 1.5G SATA 7.2K
750GB 1.5G SATA 7.2K
Up to 4
1-4
HP SC40Ge 4-Port Internal SAS
HBA with RAID 0, 1 NOTE: When using the SC40Ge with
SATA Hard Drives, 1.5G SATA Hard Drives are required. Transfer rate: 1.5
Gb/s SATA, 3 Gb/s SAS
HP Smart Array P400 Controller
HP Smart Array P800 Controller
SATA Non-Hot Plug
Enterprise (ENT) Drives 3.5"
Quantity
Supported
Position
Supported
Controller
160GB 1.5G SATA 7.2K
Up to 4
1-4
HP Embedded SATA RAID Controller NOTE: Transfer rate: 1.5 Gb/s SATA
SAS Hot Plug
3.5"Midline (MDL) Drives NOTE: Installation of the Hot Plug
Backplane 1U 2S Kit (445985-B21) is required if ordering third or fourth
Hard Drives for Hot Plug models only.
Quantity
Supported
Position
Supported
Controller
1TB 3G 7.2K
750 3G 7.2K
Up to 4
1-4
Embedded SATA with integrated
SATA RAID 0,1
HP Smart Array E200/128 BBWC Controller
HP Smart Array P400 Controller
HP Smart Array E500/256MB Controller
HP Smart Array P800 Controller
SAS Hot Plug 3.5"
Enterprise (ENT) Drives NOTE: Installation of the Hot Plug
Backplane 1U 2S Kit (445985-B21) is required if ordering third or fourth
Hard Drives for Hot Plug models only.
HP SC40Ge 4-Port Internal SAS
HBA with RAID 0, 1 NOTE: When using the SC40Ge with
SATA Hard Drives, 1.5G SATA Hard Drives are required. Transfer rate: 1.5
Gb/s SATA, 3 Gb/s SAS
HP Smart Array P400 Controller
HP Smart Array P800 Controller
NOTE: For a complete listing of compatible tape and disk-based
backup offerings, please visit:
www.hp.com/go/connect NOTE: SAS Tape Drives: Connecting hard drive cage and SAS tape to
the same SAS Controller using split cable (supplied with tape drive)
deactivates 1 of the hard drive bays. Actual hard drive bay deactivated
depends on where split cable plugs into SAS drive connector. Example: 3x
SAS cable connector plugged into SAS drive connector (5-8) on the back of
the hard drive cage would mean drive bay 8 is deactivated.
Position
Supported
Controller
Controller/HBA Option Kit Part Number
HP StorageWorks SCSI Tape Drives, External
LTO-1 Ultrium 232
LTO-2 Ultrium 448
LTO-3 Ultrium 920
LTO-3 Ultrium 960
LTO4 Ultrium 1760
LTO-4 Ultrium 1840
DAT 40
DAT 72
DAT 160
1U Rack-Mount Kit
3U Rack-Mount Kit
External
HP SC11Xe Host Bus Adapter
412911-B21
HP StorageWorks
USB Tape Drives, External
DAT 40 USB
DAT 72 USB
DAT 160 USB
1U USB Rack-Mount Kit
External
USB 2.0 Port
N/A
HP StorageWorks SAS Tape Drives, External
DAT 160 SAS
LTO-2 Ultrium 448 SAS
LTO-3 Ultrium 920 SAS
LTO-4 Ultrium 1760 SAS
LTO-4 Ultrium 1840 SAS
1U Rack-Mount Kit
3U Rack-Mount Kit
External
HP SC44Ge Host Bus Adapter
416096-B21
HP StorageWorks SCSI Tape Automation, External
DAT 72x10 Autoloader
1/8 G2 Autoloader
MSL2024
MSL4048
External
HP SC11Xe Host Bus Adapter
HP U320e SCSI Host Bus Adapter NOTE: Recommended for MSL tape
libraries.
412911-B21
AH627A
HP StorageWorks
SAS Tape Automation, External
1/8 G2 Autoloader
MSL2024
MSL4048
External
HP SC44Ge Host Bus Adapter
NOTE: Please visit:
http://www.hp.com/go/connect
for details about minimum SAS controller firmware version and SAS
cabling requirements.
416096-B21
HP StorageWorks
Fibre Tape Automation, External
MSL2024
MSL4048
MSL8096
MSL6000
External
Please consult the EBS connectivity matrix at:
http://www.hp.com/go/ebs
for detailed connectivity information.
N/A
HP StorageWorks RDX Removable Disk Backup System, External
RDX160
RDX320
RDX500
External
USB 2.0 port
N/A
HP StorageWorks D2D Backup Systems
D2D120
D2D130
D2D2503i
D2D4004i
System Leakage with all power
supplies loaded (mA)
1.58
3.03
System Inrush Current with
all power supplies loaded (A)
19
37
Power cord requirements
Nema 5-15P to IEC320-C13
IEC320-C13 to IEC320-C14
NOTE:
Power shown is for a fully configured system consisting of (2) CPU, (8)
double-sided DIMMs, (2) HDDs, (1) CD-ROM, and (2) PCI cards.
Power Cord
AF556A
Server Power Cords
One 6' Highline (IEC-IEC) power cord ships standard NOTE: HP ProLiant DL servers no
longer ship standard with NEMA power cords (163719-002) that allow
connection to 110V US wall outlets in a home or office. ProLiant DL
servers are primarily connected to PDU's in data center racks so they now
ship standard with only a PDU power cord (416151-B21). If a user wishes to
power a ProLiant DL server using a 110V receptacle (NEMA-15), the NEMA
power cord (227099-001) must be ordered separately.
If customers require a local power cord, they can check the power cord
matrix for the appropriate cord. Please see the following power cord
matrix:
http://www.hp.com/go/powercordmatrix.
- Click on the system of interest. Example: DL160 G5
- Follow the instructions of the next screens.
Power Supply Output (per
power supply)
Rated
Steady-State Power
653.10W (at 100 VAC),
653.08W (at 200 VAC)
System Inlet Temperature
Operating
50° to 95° F
(10° to 35° C) at sea level with an altitude derating of 1.8°F per every
1000 ft (1.0°C per every 305 m) above sea level to a maximum of 10,000
ft (3050 m), no direct sustained sunlight. Maximum rate of change is
18°F/hr (10°C/hr). The upper limit may be limited by the type and number
of options installed. System performance may be reduced if
operating with a fan fault or above 86°F (30°C).
Non-operating
40° to
140° F (-40° to 60° C) Maximum rate of change is 36°F/hr (20°C/hr).
Relative Humidity (non-condensing)
Operating
10% to 85%
relative humidity (Rh), 82.4°F (28°C) maximum wet bulb temperature,
non-condensing.
Non-operating
10% to 95%
relative humidity (Rh), 101.7°F (38.7°C) maximum wet bulb temperature,
non-condensing.
Altitude
Operating
10,000 ft (3050 m). This value may be limited by the type and number of
options installed. Maximum allowable altitude change rate is 1500 ft/min
(457 m/min).
Non-operating
30,000 ft (9144 m). Maximum allowable altitude change rate is 1500
ft/min (457 m/min).
Acoustic Noise
Listed are the declared A-Weighted sound power levels (LWAd) and
declared average bystander position A-Weighted sound pressure levels (LpAm)
when the product is operating in a 23°C ambient environment. Noise emissions
were measured in accordance with ISO 7779 (ECMA 74) and declared in
accordance with ISO 9296 (ECMA 109).
Idle
LWAd
6.86
LpAm
52.36dBA
Operating
LWAd
6.89
LpAm
52.60dBA
Emissions Classification (EMC)
FCC Rating
Class A
Normative Standards
CISPR 22; EN55022; EN55024; FCC CFR 47, Pt 15; ICES-003; CNS13438;
GB9254; K22;K24; EN 61000-3-2; EN 61000-3-3; EN 60950-1; IEC 60950-1
NOTE:
Product conformance to cited product specifications is based on sample
(type) testing, evaluation, or assessment. This product or family of
products is eligible to bear the appropriate compliance logos and
statements.
Non-Hot Plug SATA Hard
Drives
160-GB 7.2K
458947-B21
Capacity
160,041 MB
Height
1.028 in (2.61 cm)
Width
4.0 in (10.16 cm)
Depth
5.787 in (147.0 mm)
Interface
SATA ATA
Transfer Rate Synchronous
(Maximum)
1.5Gb/s
Seek Time
(typical reads, including settling)
Single Track
0.9 ms
Average
9.0 ms
Full-Stroke
17.8 ms
Rotational Speed
7,200 rpm
Physical
Configuration
Bytes/Sector
512
Logical Blocks
312,581,808
Operating Temperature
41° to 131° F (5° to
55° C)
Embedded NC105i PCIe
Gigabit Server Adapter
Network Interface
Integrated
10/100/1000BASE-T Transceiver
Combines a
triple-speed IEEE 802.3TM - Compliant Media Access Controller (MAC) with a
triple-speed Ethernet transceiver.
Data Transfer Method
Compliant to x1 PCIe
Specification
Network Transfer
Rate
10Base-T (Half-Duplex)
10 Mb/s
10Base-T (Full-Duplex)
20 Mb/s
100Base-TX (Half-Duplex)
100 Mb/s
100Base-TX (Full-Duplex)
200 Mb/s
1000Base-TX (Half and
Full-Duplex)
2000Mb/s
Connector
RJ-45 connector
Cable Support
Performs all the
physical layer functions for 10BASE-T, 100BASE-T, and 1000BASE-T Ethemet on
standard Category 5 UTP
Environment-friendly Products and Approach
End-of-life Management and Recycling
Hewlett-Packard offers end-of-life HP product return, trade-in, and recycling
programs in many geographic areas. For trade-in information, please go to:
http://www.hp.com/go/green. To recycle your product, please go to:
http://www.hp.com/go/green
or contact your nearest HP sales office. Products returned to HP will be
recycled, recovered or disposed of in a responsible manner.
The EU WEEE
directive (2002/95/EC) requires manufacturers to provide treatment
information for each product type for use by treatment facilities. This
information (product disassembly instructions) is posted on the Hewlett
Packard web site at:
http://www.hp.com/go/green. These instructions may be used by recyclers
and other WEEE treatment facilities as well as HP OEM customers who
integrate and re-sell HP equipment.
The information contained herein is subject to change
without notice.
Microsoft and Windows NT are US
registered trademarks of Microsoft Corporation. Intel, the Intel logo,
Xeon and Xeon Inside are trademarks of Intel Corporation in the U.S. and
other countries.
The only warranties for HP
products and services are set forth in the express warranty statements
accompanying such products and services. Nothing herein should be
construed as constituting an additional warranty. HP shall not be liable
for technical or editorial errors or omissions contained herein.
For hard drives, 1GB = 1 billion bytes. Actual formatted capacity is less.